Please enable JavaScript to view this site.

MaxxECU online help

Traction control

 

enable

Enable or disable the traction control system.

 

min speed

Specifies minimum speed to enable the traction control system.

 

cut ramp in

Enables the possibility to add a max cut in % depending on undriven wheel speed, mostly used on the lower speeds to prevent engine "stalling" when cutting to much power.

 

clip0867

Maximum cut in % at Undriven wheel avg speed.

 

 

PID control

 

P gain

Proportional value.

 

I gain

Integral value.

 

D gain

Derivative value.

 

Limiter decay

When a cut % is activated, this setting specifies how fast does the cut return to 0%.

 

see, PID control.

 

 

Dual PID

 

Used on high horse power vehicles where a faster PID is required at low speed than at higher speeds.

 

enable

Enable or disable the dual PID control.

 

P gain at high speed

Proportional value at high speed.

 

I gain at high speed

Integral value at high speed.

 

D gain at high speed

Derivative value at high speed.

 

low pid setpoint speed

Low Speed threshold.

 

High pid setpoint speed

High speed threshold.

 

Note: Below the low setpoint speed, it uses the lower PID settings, between the low and high threshold, the PID settings are interpolated, until the high threshold, at which only the high settings are used.

 

 

Power limiting

 

power limit type

Specifies how the Traction control system will reduce power to gain traction.

Ignition cut - Most effective way of reducing engine power in the fastest way (but make sure your engine can handle such ignition cuts).

fuel cut.

Ignition retard + ignition cut

Ignition retard + fuel cut

 

max ignition retard

Maximum ignition retard during traction control.

 

Retard range

The % of power cut where full retard is applied. When the retard range is maxed out, it also begins cutting power with ign/fuel drops. Normal range 20-50%.

Ex. if set to 30%, maximum retard is 30% of the above maximum ignition retard value, then ignition/fuel cut is applied.

Set to 50%

 

 

Examples

 

To be able to use Traction control, at least two wheel speeds must be available, using CAN input or wheel speed sensor wired to digital inputs.

In the following example we are using three wheel speed sensors, and assumes they are properly configured as Speedsensor wheelspeed front/rear right/left and calibrated.

 

clip0080

Wheel speed sensors connected and working in MaxxECU.

 

 

clip0087

Traction --> Traction control setup settings page. Enable, always on is the preferable way of using this function, to disable it, use the digital function Disable traction.

 

Note: Always test and tune a traction system on a closed road/airport or similar. Power limit type Ignition cut is the most effective way of limiting power.

 

 

traction control target slip table

 

The traction control target slip table used by the traction control system, as all tables in MaxxECU you can select any available axis in the system, or even add 4D to the tables,

 

clip0091

Traction --> Tractionctrl Target Slip configuration. Axis can of course be changed to almost everything available in MaxxECU. Enter your target wheel slip. 10-25% depending on tire choice is a good value to start of with.

 

 

clip0088

Using MaxxECU built in Live-logger (or in this case external logviewer) we can determine wheel slip (%) and power limit (%), which is calculated in realtime. In the above example the vehicle has launched, and rear wheels (Driven wheels) are spinning...

Since Undriven wheel speed are only 16,4km/h the traction system is not engaged (min speed in this example is 40km/h).

 

 

clip0089

RealTime Data value Power limit in working 100% to maintain wheel slip (currently 60%).

 

 

clip0090

Another example of power limiting to maintain target wheel slip.

 

 

How to get faster on the run with MaxxECU

It's all about logging and testing!

 

1.Use a boost controller with Gear adjustment, try to achieve wheel slip target.

2.Good and properly configured Launch settings.

3.Activate Distance counters and log the run, if no access to a drag strip is available...

4.Run and log, compare RealTime Data value Power limit and Target slip. Run and log again...